Internationalllc

January 6, 2004

United States

International Motors, LLC

ON CERTAIN SCHOOL BUSES, AN INCORRECT BRAKE PEDAL WAS INSTALLED, LEADING TO MISALIGNMENT. MISALIGNMENT, IN CONJUNCTION WITH A FORCE ACTUATED BRAKE SWITCH, CAN CAUSE DELAYED BRAKE LIGHT ACTIVATION DURING LIGHT BRAKING APPLICATIONS.

January 5, 2004

United States

International Motors, LLC

ON CERTAIN AMBULANCES EQUIPPED WITH GOODRICH VELVET-RIDE REAR SUSPENSION SYSTEMS, THE BOLTS CONNECTING THE SUSPENSION SPRING TO THE REAR AXLE MAY BREAK.

October 22, 2003

United States

International Motors, LLC

ON CERTAIN TRUCKS EQUIPPED WITH V8 ENGINES AND AIR BRAKES OR AIR OPERATED PARK BRAKES, A STAND-OFF BRACKET WAS NOT INSTALLED. THE BRACKET SUPPORTS THE COPPER AIR COMPRESSOR DISCHARGE TUBE.

July 28, 2003

United States

International Motors, LLC

ON CERTAIN HEAVY DUTY TRUCKS, THE DRAG LINK WILL INTERFERE WITH THE FRONT, DRIVER'S SIDE, BRAKE CHAMBER AND SLACK ADJUSTER. THIS INTERFERENCE COULD CAUSE DAMAGE TO THE SLACK ADJUSTER AND RENDER IT INOPERABLE.

May 21, 2003

United States

International Motors, LLC

ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH DANA SPICER E-12021 12,000 LB. , E-1202W 12,000 LB.

May 1, 2003

United States

International Motors, LLC

ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH CATERPILLAR ENGINES, A SINGLE BANK TYPE EXHAUST CLAMP WAS INSTALLED ON THE TAIL PIPES INSTEAD OF A DOUBLE BAND TYPE CLAMP.

March 6, 2003

United States

International Motors, LLC

ON CERTAIN HEAVY DUTY TRUCKS BUILT WITH INTERNATIONAL CODE 16SCH (LOWER BUNK WEBBING RESTRAINT). FOUR BOLTS HOLD THE BUNK WEBBING RESTRAINT LATCH BRACKETS TO THE BUNK BASE. United States

International Motors, LLC

ON CERTAIN HEAVY DUTY TRUCKS BUILT WITH A DETROIT ENGINE AND A LEECE NEVILLE ALTERNATOR. THE ELECTRICAL TERMINAL AT THE ALTERNATOR END OF THE CABLE THAT RUNS FROM THE STARTER TO THE BATTERY STUD ON THE ALTERNATOR MAY BREAK OFF, DUE TO VIBRATION IN THE CABLE. United States

International Motors, LLC

CERTAIN HEAVY DUTY TRUCKS FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 104, "WINDSHIELD WIPING AND WASHING SYSTEMS. United States

International Motors, LLC

ON CERTAIN HEAVY DUTY TRUCKS BUILT WITH A CATERPILLAR ENGINE WITH A 4 DEGREE TILT, THE STARTER FIELD-STUD MAY CONTACT THE FRAME RAIL BECAUSE OF VARIATIONS IN THE AIR GAP BETWEEN THE FIELD STUD AND THE FRAME RAIL. SHOULD THE STARTER FIELD STUD CONTACT THE FRAME RAIL, THERE WOULD BE A DIRECT FULL BATTERY SHORT TO THE…

January 28, 2003

United States

International Motors, LLC

CERTAIN SCHOOL BUSES AND HEAVY DUTY TRUCKS BUILT WITH HYDRAULIC BRAKES AND AN AIR POWERED PARKING BRAKE (BRAKE CODE 04GAS) FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 105, "HYDRAULIC AND ELECTRIC BRAKE SYSTEMS.

November 15, 2002

United States

International Motors, LLC

ON CERTAIN HEAVY DUTY TRUCKS, THE BOLTS AND LOCKING NUTS USED TO HOLD THE BRAKE SPIDERS OR BRAKE ANCHOR PLATES TIGHT TO THE AXLES WERE UNDER-TORQUED ON THE RIGHT SIDE OF THE VEHICLES. IF THE CLAMP LOAD ON THE BOLTS IS NOT SUFFICIENT, THE ANCHOR PLATE MAY MOVE WHEN THE BRAKE IS APPLIED IN EITHER THE FORWARD OR REVERSE…

September 25, 2002

United States

International Motors, LLC

ON CERTAIN HEAVY DUTY TRUCKS, THE JOINT BETWEEN THE LOWER PORTION OF THE STEERING COLUMN AND THE UPPER END OF THE INTERMEDIATE STEERING SHAFT MAY HAVE A MISSING OR LOOSE PINCH BOLT. THIS CONDITION COULD ALSO OCCUR AT THE LOWER END OF THE INTERMEDIATE STEERING SHAFT AT THE STEERING GEAR CONNECTION.

September 20, 2002

United States

International Motors, LLC

ON CERTAIN MEDIUM AND HEAVY DUTY TRUCKS BUILT WITH DRIVELINE PARKING BRAKE CODES 04GAR, THE PARKING BRAKE ASSEMBLY MAY NOT HOLD THE VEHICLE IN POSITION WHEN SET. FACTORS CONTRIBUTING TO THIS POSSIBILITY ARE AS FOLLOWS: (1) CRACKED OR BROKEN CAMS; (2) LOOSE OR BROKEN ANCHOR BOLTS; (3) INITIAL SHOE DIAMETER NOT SET… United States

International Motors, LLC

ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH BENDIX TC-7 TRAILER CONTROL HAND-OPERATED VALVE WITH PUSH-TO-CONNECT FITTINGS. THE DELIVERY PORT IN THE VALVE BODY MAY BE PARTIALLY BLOCKED DUE TO A PROBLEM DURING THE MODING PROCESS.

July 26, 2002

United States

International Motors, LLC

ON CERTAIN HEAVY DUTY TRUCKS, THE FUEL LINE IS ROUTED TOO CLOSE TO A TURBO CHARGER OUTLET/EXHAUST PIPE. IF AN INTERFERENCE CONDITION OCCURS BETWEEN THE FUEL HARNESS AND THE EXHAUST PIPE, THE FUEL LINE INSIDE THE REFLECTIVE HEAT WRAP COULD MELT DUE TO EXCESSIVE HEAT. United States

International Motors, LLC

ON CERTAIN SCHOOL BUSES AND HEAVY DUTY TRUCKS BUILT WITH INTERNATIONAL VT365 ENGINES AND MANUFACTURED AT INTERNATIONAL DIESEL OF ALABAMA. THE INJECTOR DRIVER MODULES (IDM) BUILT FOR THE VT365 ENGINES COULD HAVE MISSING VIBRATION DAMPING/RETENTION SHELLS AND A MISSING HOT-MELT PROCESS ON THE DC/DC BOARDS.

March 22, 2002

United States

International Motors, LLC

ON CERTAIN TRUCKS, THE COTTER PIN THAT GOES THROUGH THE DRAG LINK BALL STUD AT THE CONNECTION TO THE PITMAN ARM IS MISSING. THIS PIN PREVENTS THE CASTLE NUT FROM LOOSENING. United States

International Motors, LLC

CERTAIN TRUCKS EQUIPPED WITH ENGINE STARTERS (CODE 08WWN OR 08WWP) BUILT BY LEECE-NEVILLE. THESE STARTERS HAVE A DEFECTIVE TERMINAL ADAPTER STUD.

February 15, 2002

United States

International Motors, LLC

ON CERTAIN HEAVY DUTY TRUCKS EQUIPPED WITH IROS REAR AIR SUSPENSIONS, DURING ASSEMBLY, FOUR BOLTS AND NUTS HOLDING THE MAIN SUPPORT MEMBER BUSHING BAR PINS TO THE MAIN SUPPORT MEMBER HANGERS WERE INCORRECTLY TIGHTENED.