Internationaltruckenginecorporation

September 17, 1998

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH A 1710 DRIVE LINE AND A 12 X 4 HYDRAULIC PARKING BRAKE. IF THE BRAKE DRUM OR TRANSMISSION YOKE ARE NOT FULLY SEATED WHEN THE EIGHT BOLTS ARE INSTALLED CONNECTING THE 3-PIECE JOINT, THE BOLTS CAN LOOSEN.

July 28, 1998

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: HEAVY DUTY 4X4 AND 6X6 TRUCKS EQUIPPED WITH FABCO 12,000 POUND FRONT DRIVE AXLES. THE INTEGRAL TIE ROD ARM OF THESE AXLES FRACTURES FROM THE SPINDLE YOKE.

June 16, 1998

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH AFTERMARKET ALUMINUM DUAL WHEELS, 22. 5X8.

May 27, 1998

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: TRUCKS, SCHOOL BUSES AND TRANSIT BUSES EQUIPPED WITH AN OPTIONAL AUTOMATIC TRANSMISSION SHIFT LEVER THAT INCLUDES A PARK BRAKE POSITION. THE TRANSMISSION SHIFTER/PARK BRAKE LEVER CAN BIND BEFORE FULLY ENGAGING IN THE PARK BRAKE POSITION CAUSING A FALSE PARK CONDITION. United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH PROSLEEPER BUNKS. A MICRO RELAY LOCATED BEHIND THE HVAC CONTROL PANEL IN THE BUNK CAN CORRODE FROM MOISTURE.

March 25, 1998

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH CATERPILLAR C-10 OR C-12 ENGINES. A BRACKET OR P-CLAMP AT THE REAR OF THE ENGINE THAT SUPPORTS THE COMPRESSOR DISCHARGE LINE WAS OMITTED.

November 24, 1997

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH DESIGN LEVEL 1, ROCKWELL FF980 SERIES FRONT AXLE. THE FRONT AXLE HUB FLANGE CAN DEVELOP CRACKS DUE TO HIGH STRESS LEVELS.

September 8, 1997

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: BUSES AND HEAVY TRUCK CHASSIS EQUIPPED WITH CUMMINS N-14, CATERPILLAR, AND DETROIT DIESEL ELECTRONIC ENGINES. THE ACCELERATOR PEDAL ROD MATERIAL IS EXCESSIVELY BRITTLE AND CAN BREAK DURING A FULL THROTTLE APPLICATION. United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: BUSES AND HEAVY TRUCK CHASSIS EQUIPPED WITH T444E ENGINES. THE ACCELERATOR PEDAL ROD MATERIAL IS EXCESSIVELY BRITTLE AND CAN BREAK DURING A FULL THROTTLE APPLICATION.

September 2, 1997

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: HEAVY DUTY TRUCK. THE SHOULDER BOLT WHICH HOLDS THE GROTE TURN SIGNAL SWITCH CASE AND COMPONENTS TOGETHER CAN LOOSEN RESULTING IN THE TURN SIGNAL MALFUNCTIONING.

July 29, 1997

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH ANTILOCK BRAKE SYSTEM (ABS). THE WIRING FROM THE ELECTRONIC CONTROL UNIT WAS CONNECTED TO THE WRONG WHEEL SENSOR.

July 28, 1997

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: HEAVY DUTY TRUCKS EQUIPPED WITH SIX-SPOKE WHEEL ASSEMBLIES. THESE VEHICLES WERE MANUFACTURED WITH THE WRONG COMBINATIONS OF WHEEL ASSEMBLY PARTS.

May 28, 1997

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: MEDIUM AND HEAVY DUTY TRUCKS, SCHOOL AND TRANSIT BUSES BUILT WITH A BENDIX 9X3 POWER APPLY PARK BRAKE SYSTEM. THE CAM LEVER OF THE POWERED APPLY BRAKE CAN MOVE FORWARD, BECAUSE A HOLE IN THE TRANSMISSION MOUNTING BOSS WAS DRILLED TOO DEEP.

December 12, 1996

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

THESE VEHICLES ARE EQUIPPED WITH A DETROIT DIESEL OPTIMIZED IDLE SYSTEM. IF THE IGNITION IS TURNED ON AND THE FUSE FOR THE ELECTRONIC CONTROL MODULE (ECM) POWER FEED LINE IS REMOVED OR BURNED OUT, UNINTENTIONAL CRANKING OF THE ENGINE WILL OCCUR..

November 27, 1996

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: SCHOOL BUSES AND HEAVY DUTY TRUCKS EQUIPPED WITH REAR AXLE ASSEMBLIES PRODUCED BY DANA SPICER. CERTAIN REAR AXLE ASSEMBLIES WERE IMPROPERLY HEAT TREATED WHICH COULD ALLOW PINION BREAKAGE AT THE PINION THREADS. United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

VEHICLE DESCRIPTION: SCHOOL BUSES EQUIPPED WITH THE INTERNATIONAL I6 ELECTRONIC ENGINE AND AN EXTRA THICK BUS BODY FLOOR. THE ACCELERATOR PEDAL TO FLOOR CLEARANCE IS APPROXIMATELY 1.

November 22, 1996

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

THE DRIVE AXLE HOUSINGS CONSIST OF A PLATE STEEL CENTER SECTION AND TWO FORGED SPINDLES, ONE OF WHICH IS WELDED TO EACH END OF THE CENTER SECTION. EACH SPINDLE CONTAINS A KEYWAY SLOT IN WHICH THE LOCKING TAB FOR THE WHEEL BEARING NUT LOCKING MECHANISM IS INSERTED.

November 12, 1996

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

THESE BUSES HAVE A TURN SIGNAL LEVER THAT WILL NOT OPERATE CONSISTENTLY IN THE LANE CHANGE MODE IF THE LEVER IS NOT MOVED TO THE POSITION WHERE RESISTANCE TO MOVEMENT IS FELT.

September 13, 1996

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

THE WIRING FROM THE ELECTRONIC CONTROL UNIT WAS CONNECTED TO THE WRONG WHEEL SENSOR OR TO THE WRONG BRAKE MODULATOR VALVE. IT IS POSSIBLE THAT EITHER OR BOTH WIRING MAY HAVE OCCURRED AT EITHER THE FRONT OR REAR AXLE OR BOTH AXLES.

August 20, 1996

United States

INTERNATIONAL TRUCK & ENGINE CORPORATION

THE STEERING COLUMN USED WAS INCORRECTLY MANUFACTURED. THE TUBE PORTION OF THE STEERING COLUMN HAS A WELDED END WITH A SPECIFIED LENGTH OF 5.