Ford

October 23, 1978

United States

Ford Motor Company

DUE TO AN ERROR IN THE VEHICLE ASSEMBLY COMPUTER BROADCAST PROGRAM, THE INVOLVED VEHICLES WERE EQUIPPED WITH 14X5. 5 INCH WHEEL RIMS WHICH WERE INTENDED FOR USE ON PASSENGER CARS.

October 17, 1978

United States

Ford Motor Company

THE ENGINE COOLING FAN BLADES MAY CRACK UNDER HIGH SPEED OPERATING CONDITIONS. FRAGMENTS MAY SEPARATE AND DAMAGE THE ENGINE COMPONENTS, AND IF THE HOOD IS OPEN AND THE ENGINE IS RUNNING, BLADE FRAGMENTS COULD FLY OUT FROM THE VEHICLE AND INJURE NEARBY PERSONS.

October 11, 1978

United States

Ford Motor Company

THE INVOLVED WHEELS CONTAIN MISLOCATED STEM HOLES. THIS MAY ALLOW AIR LEAKAGE AT THE TIRE VALVE STEM, UNDER HIGH SPEED DRIVING CONDITIONS.

October 5, 1978

United States

Ford Motor Company

ON THE INVOLVED VEHICLES, THE POTENTIAL EXISTS FOR THE OUTBOARD SEAT BELTS TO BECOME TRAPPED IN THE SEAT-BED PIVOTING MECHANISM. SHOULD THE BELT BECOME TRAPPED IN THE MECHANISM WHEN THE SEAT IS CONVERTED TO A BED, THE BELT MAY BECOME CUT OR FRAYED.

October 4, 1978

United States

Ford Motor Company

ONE OR MORE OF THE FIVE COOLING FAN BLADES MAY HAVE BEEN IMPROPERLY RIVETED TO THE FAN SPIDER. THIS COULD ALLOW THE BLADES TO SEPARATE FROM THE FAN DURING ENGINE OPERATION. United States

Ford Motor Company

THE LOWER STEERING SHAFT ASSEMBLIES CONTAIN COUPLING RIVET PINS WHICH WERE NOT RIVETED SECURELY ENOUGH DURING MANUFACTURE. CONSEQUENTLY ONE OR BOTH OF THE PINS COULD LOOSEN FROM THE FLANGE OF THE FLEXIBLE COUPLING DURING VEHICLE OPERATION. United States

Ford Motor Company

THE INVOLVED VEHICLES ARE EQUIPPED WITH FLEXIBLE COOLING FAN BLADES THAT MAY CRACK WHEN SUBJECTED TO HIGH ENGINE SPEED OPERATING CONDITIONS. FAN BLADE CRACKING CAN LEAD TO FRAGMENTS SEPARATING FROM THE FAN.

September 25, 1978

United States

Ford Motor Company

THE FULL SIZE SEDANS WERE EQUIPPED WITH INCORRECT TAIL LAMP SOCKETS AND THE FULL SIZE STATION WAGONS WERE INSTALLED WITH INCORRECT TAIL LAMP AND BACK UP LAMP SOCKETS. THEREFORE THESE VEHICLES FAIL TO COMPLY WITH THE PHOTOMETRIC REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO.

September 21, 1978

United States

Ford Motor Company

THE INVOLVED VEHICLES CONTAIN EMISSION CONTROL SYSTEMS THAT UTILIZE A PULSE AIR REED VALVE TO PERMIT AIR FLOW FROM THE AIR CLEANER TO THE EXHAUST MANIFOLD ON NEGATIVE PRESSURE PULSATIONS. THESE REED VALVES MAY FAIL UNDER COLD WEATHER CONDITIONS, CAUSING A BACKFLOW OF EXHAUST GAS INTO THE AIR CLEANER AND FUEL…

September 15, 1978

United States

Ford Motor Company

THESE TRANSMISSIONS MAY CONTAIN IMPROPERLY MANUFACTURED PARKING PAWL ACTUATING RODS. CONSEQUENTLY, THE UNHARDENED CAM SURFACE OF THESE RODS CAN ALLOW THE ROD TO DEFORM DURING USE WITH RESULTANT INCREASE IN SHIFT EFFORTS AND DIFFICULTY IN RELEASING THE PARKING PAWL AND ENGAGING THE PARKING GEAR.

September 11, 1978

United States

Ford Motor Company

United States

Ford Motor Company

THE WINDSHIELD WIPER AND WASHER SYSTEM CONTAINS AN INCORRECT 6 AMP CIRCUIT BREAKER INSTEAD OF THE 8. 25 AMP CIRCUIT BREAKER. United States

Ford Motor Company

THE INVOLVED VEHICLES DO NOT CONTAIN A FUEL TANK SHIELD AT THE FRONT RIGHT CORNER OF THE MID-SHIP FUEL TANK. IN THE EVENT OF A FRONTAL IMPACT, EXCESSIVE FUEL SPILLAGE FROM THE FUEL TANK MAY OCCUR.

August 24, 1978

United States

Ford Motor Company

THE TILT STEERING COLUMNS ON THE INVOLVED VEHICLES CONTAIN IN-PROCESS TEMPORARY ALIGNMENT PINS RATHER THAN THE PERMANENT PRESS-FIT PIVOT PINS. THE TEMPORARY PINS ARE SLIGHTLY UNDERSIZED AND COULD SEPARATE FROM THE STEERING COLUMN DURING VEHICLE OPERATION.

August 15, 1978

United States

Ford Motor Company

THE WIPER ARMS COULD SEPARATE FROM THE PIVOT SHAFTS, RENDERING THE WIPERS INOPERATIVE.

August 7, 1978

United States

Ford Motor Company

THE DRIVER"S SIDE SHOULDER BELT RETRACTOR MOUNTING BRACKET ASSEMBLY CONTAINS A WELD NUT WHICH WAS IMPROPERLY ATTACHED TO THE BRACKET. THIS FAILS TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. United States

Ford Motor Company

THE WINDSHIELD WIPER DRIVE LINKAGE ON THE AFFECTED VEHICLES MAY FRACTURE DUE TO METAL FATIGUE AS A RESULT OF REPEATED FLEXING OF THE DRIVE ARM ACROSS A STRESS SENSITIVE AREA. THIS CONDITION WILL RENDER THE WINDSHIELD WIPER SYSTEM INOPERATIVE.

July 25, 1978

United States

Ford Motor Company

THE INVOLVED VEHICLES WERE ASSEMBLED WITHOUT THE INTENDED WINDSHIELD WEATHERSTRIP LOWER RETAINER. THESE VEHICLES FAIL TO COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO.

July 3, 1978

United States

Ford Motor Company

THE ENGINE COOLING FAN BLADES MAY CRACK AND CHIP DUE TO HIGH STRESSES CAUSED BY VIBRATIONS. THE CHIPPED PIECES OF THE BLADE COULD FLY INTO THE UNDERHOOD COMPONENTS.

June 27, 1978

United States

Ford Motor Company

AN IMPROPER TRANSMISSION SHIFT BRACKET WAS INSTALLED WHICH, BECAUSE OF ITS DESIGN, COULD CONTACT AND ABRADE THE FUEL HOSE. FUEL LEAKAGE AND POSSIBLE ACCUMULATION OF FUEL ON A SURFACE BENEATH A PARKED VEHICLE COULD RESULT.