Ford

May 15, 1979

United States

Ford Motor Company

THE INVOLVED VEHICLES WERE PRODUCED WITH BRAKE PUSH-ROD TO BRAKE PEDAL RETAINING PINS WHICH WERE NOT HEAT-TREATED AS SPECIFIED. THIS COULD ALLOW THE BRAKE PEDAL TO BECOME DISENGAGED FROM THE PUSH-ROD. United States

Ford Motor Company

THE INVOLVED VEHICLES WERE PRODUCED WITH FRAMES THAT MAY HAVE INADEQUATELY WELDED #2 CROSSMEMBER ASSEMBLIES. THIS COULD OCCUR IF CERTAIN MANUAL WELD OPERATIONS WERE NOT PERFORMED DURING FRAME FABRICATION.

April 30, 1979

United States

Ford Motor Company

SOME VEHICLES WERE PRODUCED WITH BRAKE CONTROL VALVES AND BRAKE TUBES INTENDED FOR USE IN VEHICLES WITHOUT TRAILER TOW PACKAGES. United States

Ford Motor Company

SOME OF THESE VEHICLES WERE PRODUCED WITH MISINDEXED FRONT BRAKE HOSES WHICH COULD CONTACT A TIRE OR WHEEL IN A FULL-TURN CONDITION. CHAFING AND WEAR TO THE BRAKE HOSE COULD RESULT IN LOSS OF BRAKE FLUID AND FRONT WHEEL BRAKING CAPABILITY.

April 5, 1979

United States

Ford Motor Company

WITH THE ENGINE OPERATING AT HIGH SPEED, THE PLASTIC ENGINE FAN FINGER GUARDS MAY CONTACT THE ENGINE FAN AND BREAKAGE OF THE GUARD MAY OCCUR. THIS COULD CAUSE FRAGMENTS OF THE FINGER GUARD TO SCATTER.

March 29, 1979

United States

Ford Motor Company

CERTAIN AIR BRAKE ANTI-LOCK MODULATORS COULD MALFUNCTION DURING OPERATION OF THE ANTI-LOCK SYSTEM. A NYLON PISTON WITHIN THE MODULATOR AIR VALVE SYSTEM CAN SWELL FROM EXPOSURE TO SYSTEM CONTAMINANTS.

March 6, 1979

United States

Ford Motor Company

USE OF AN ALTERNATE ALUMINUM ALLOY WHICH HAS A LOWER STRENGTH IN HOT STATE, MAY ALLOW CRACKING OF BRAKE PEDAL LEVERS. REPEATED BRAKING OR HIGH BRAKE PEDAL LOADING MAY RESULT IN COMPLETE FRACTURE WHICH WOULD PREVENT APPLICATION OF THE SERVICE BRAKES.

March 1, 1979

United States

Ford Motor Company

VEHICLES FAIL TO CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 110, "TIRE SELECTIN AND RIMS".

February 22, 1979

United States

Ford Motor Company

THE AIR BRAKE LINES MAY BE ROUTED TOO CLOSE TO THE EXHAUST MUFFLER. BECAUSE THE AIR BRAKE LINES ARE MADE OF NYLON MATERIAL, HEAT FROM THE EXHAUST MUFFLER CAN WEAKEN THE BRAKE LINE TUBES, POSSIBLY CAUSING THEM TO RUPTURE. United States

Ford Motor Company

AN INCORRECT STEERING GEAR FLANGE MAY HAVE BEEN INSTALLED, WHICH MAY SLIP AND CAUSE EVENTUAL LOSS OF STEERING CONTROL.

January 29, 1979

United States

Ford Motor Company

THE INVOLVED VEHICLES WERE ASSEMBLED WITH IMPROPERLY MANUFACTURED STEERING ARM KNUCKLES. SHOULD AN IMPROPERLY MANUFACTURED STEERING ARM KNUCKLE FRACTURE AND SEPARATE, THE STEERING LINKAGE TIE ROD MAY DISENGAGE FROM THE KNUCKLE.

January 26, 1979

United States

Ford Motor Company

THE INVOLVED VEHICLES WERE BUILT WITH SAFETY COMPLIANCE CERTIFICATION LABELS THAT CONTAINED INCORRECT GVWR AND GAWR WEIGHT INFORMATION. THE GVWR"S COULD BE OVERSTATED BY UP TO 197 LBS. United States

Ford Motor Company

THE INVOLVED VEHICLES WERE MANUFACTURED WITHOUT A FUEL TANK SHIELD AT THE FRONT RIGHT CORNER OF THE MIDSHIP FUEL TANK. AS A RESULT, THE VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO.

January 15, 1979

United States

Ford Motor Company

THE WORD "LIGHTS" WAS OMITTED FROM THE PANEL APPLIQUE IDENTIFYING THE HEADLAMP SWITCH. WITHOUT THIS IDENTIFICATION THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. United States

Ford Motor Company

THE INVOLVED VEHICLES DO NOT CONFORM TO FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. 212, "WINDSHIELD MOUNTING", IN THAT SOME OF THE VEHICLES WERE BUILT WITHOUT THE SPECIFIED WINDSHIELD WEATHERSTRIP RETAINING COMPONENTS.

January 9, 1979

United States

Ford Motor Company

THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH INCORRECT WELD NUTS THAT ATTACH THE REAR PORTION OF THE FRONT OUTBOARD SEAT TRACK TO THE FLOOR PAN. THE INCORRECT NUTS HAVE AN OVERSIZE DIAMETER AND THREAD, AND UPON FRONT SEAT TRACK ANCHOR BOLT INSTALLATION, THE THREADS MAY HAVE BEEN STRIPPED. United States

Ford Motor Company

SOME OF THE INVOLVED VEHICLES DO NOT HAVE THE HAIR PIN CLIP USED TO RETAIN THE PUSHROD TO THE BRAKE PEDAL PUSHROD PIN INSTALLED. IF THIS CLIP IS MISSING, THE PUSHROD MAY BECOME DISENGAGED FROM THE BRAKE PEDAL PUSHROD PIN.

December 21, 1978

United States

Ford Motor Company

THE STEERING GEARS ON THE INVOLVED VEHICLES MAY HAVE BEEN BUILT WITH IMPROPERLY MANUFACTURED SECTOR SHAFTS FROM WHICH THE THREADED PORTIONS OF THE SHAFTS MAY FRACTURE AND SEPARATE. SHOULD THE SECTOR SHAFT FRACTURE, THE PITMAN ARM MAY DISENGAGE FROM THE SPLINED PORTION OF THE SECTOR SHAFT.

December 20, 1978

United States

Ford Motor Company

THE FLUID RETURN HOSE INSTALLED BETWEEN THE POWER STEERING RESERVOIR AND PUMP IS SUSCEPTIBLE TO DETERIORATION AND "KINKING". DETERIORATION OF THE HOSE PERMITS PARTICLES TO ENTER THE POWER STEERING FLUID SYSTEM RESTRICTING FLOW.

November 27, 1978

United States

Ford Motor Company

THE INVOLVED VEHICLES WERE EQUIPPED WITH AUTOMATIC TRANSMISSIONS IN WHICH THE PARKING PAWL WAS NOT HEAT-TREATED. DURING NORMAL VEHICLE OPERATION, A PARKING PAWL THAT HAS NOT BEEN HEAT-TREATED COULD BECOME DEFORMED OR WORN TO THE POINT THAT THE TRANSMISSION WILL NOT LOCK IN "PARK".