Wilsontrailer

September 5, 2023

United States

Wilson Trailer Company

Wilson Trailer Company (Wilson) is recalling one 2024 DWH-750 Pacesetter Grain trailer, equipped with a Tire Pilot Plus tire pressure regulation system (TPRS). All 8 tires may experience a loss of tire pressure while driving faster than 45 mph.

April 2, 2019

United States

Wilson Trailer Company

Wilson Trailer Company (Wilson) is recalling certain 2019-2020 Punch Side Gooseneck Livestock trailers. The axles may lack the proper amount of grease on the inner and outer bearings on the hubs, which may lead to bearing failure.

July 1, 2016

United States

Wilson Trailer Company

Wilson Trailer Company (Wilson) is recalling certain model year 2015 DWH-550, and CD-1080 trailers manufactured November 20, 2015, equipped with certain Bendix SR5 spring brake valves. These valves may have been improperly machined which may cause a delay of application of the spring brakes while parking.

July 10, 2015

United States

Wilson Trailer Company

Wilson Trailer Company (Wilson) is recalling certain model year 2006-2015 Grain trailers manufactured January 1, 2006, to March 31, 2015. In the the affected trailers, the welds that attach the bolster plate to the pickup plate around the kingpin may fail.

July 25, 2014

United States

Wilson Trailer Company

Wilson Trailer Company (Wilson) is recalling certain model year 2014-2015 Grain and Livestock trailers manufactured September 20, 2013, to July 18, 2014, and equipped with certain Pivot Bolts Part Number 93201070. The affected pivot bolts may experience an intergranular quench crack where the bolt head meets the body…

January 30, 2013

United States

Wilson Trailer Company

Wilson Trailer Company (Wilson Trailer) is recalling certain model year 2007-2013 livestock trailers manufactured from January 2, 2007, through November 30, 2012, and equipped with a lift deck in the nose compartment. The plastic deck guides on the lift deck in the nose compartment can fail to provide proper tracking…

May 10, 2012

United States

Wilson Trailer Company

WILSON TRAILER COMPANY (WILSON TRAILER) IS RECALLING CERTAIN MODEL YEAR 2012 GOOSENECK TRAILERS EQUIPPED WITH DEXTER ELECTRIC/HYDRAULIC (E/H) BRAKE ACTUATOR PUMPS. SOME OF THESE PUMPS MAY NOT HAVE BEEN PROPERLY HEAT TREATED.

September 22, 2011

United States

Wilson Trailer Company

WILSON TRAILER IS RECALLING CERTAIN MODEL YEAR 2011 GRAIN TRAILERS MANUFACTURED FROM OCTOBER 15, 2010, THROUGH JANUARY 31, 2011, AND EQUIPPED WITH GUNITE AUTOMATIC SLACK ADJUSTERS. DUE TO AN INCOMPLETE "KNITTING" OF THE IRON AT THE TIME OF CASTING, INADEQUATE STRUCTURAL INTEGRITY OF THE SLACK ADJUSTER HOUSING CAN…

February 25, 2010

United States

Wilson Trailer Company

WILSON TRAILER IS RECALLING CERTAIN MODEL YEAR 2000 THROUGH 2008 LIVESTOCK TRAILERS MANUFACTURED BETWEEN MARCH 1, 2000 AND AUGUST 1, 2008. THE CROSS CHANNEL BETWEEN THE FRONT AND REAR SUSPENSION HANGERS CAN BREAK AND, IF UNDETECTED, OVER TIME CAN CAUSE THE FRAME TO FLEX CAUSING SEVERE CRACKING OF THE FRAME.

April 30, 2009

United States

Wilson Trailer Company

WILSON TRAILERS IS RECALLING 7,429 MY 1999-2009 GOOSENECK TRAILERS. THE DEFECT CONCERNS THE LOCK SUPPORT TUBE THAT MAY HAVE BEEN INSTALLED BEYOND SPECIFICATION.

November 19, 2008

United States

Wilson Trailer Company

WILSON TRAILERS IS RECALLING 211 MY 2009 GRAIN TRAILERS. THE PIVOT BOLTS WERE LOOSENED AT INSTALLATION AND WERE NOT PROPERLY RE-TORQUED.

September 28, 2007

United States

Wilson Trailer Company

ON CERTAIN GRAIN TRAILERS, THE FASTENERS IN THE REAR MOUNTING ANGLES OF THE ALUMINUM KING PIN RUNNER ATTACHMENT TO THE I-BEAM CAN FAIL.

September 7, 2006

United States

Wilson Trailer Company

ON CERTAIN GRAIN TRAILERS, A FATIGUE FAILURE (CRACKING) OF THE ALUMINUM ANGLE BEHIND THE KING PIN SUPPORT BEAM CAN OCCUR CAUSING DISTORTION OF THE BOTTOM RAIL AND COMPROMISING THE KING PIN ASSEMBLY.

July 12, 2006

United States

Wilson Trailer Company

ON CERTAIN TRAILERS EQUIPPED WITH HOLLAND SUSPENSIONS, THE SUSPENSION BEAM CASTING MAY HAVE A CRACK AT THE INBOARD, UPPER FLANGE NEAR THE SHOCK MOUNT.

January 31, 2006

United States

Wilson Trailer Company

ON CERTAIN TRAILERS, THE AIR RIDE SUSPENSION HANGER WELD MAY FAIL AT THE ATTACHMENT POINT BETWEEN THE HANGER AND THE SUBFRAME.

September 15, 2004

United States

Wilson Trailer Company

ON CERTAIN TRAILERS, THE WHEEL ASSEMBLY HUB SPINDLE NUT ON EACH AXLE MAY HAVE BEEN INSTALLED WITHOUT A "KEEPER. " THE PURPOSE OF THE KEEPER IS TO LOCK THE SPINDLE NUT IN PLACE AND, THEREBY, SECURE THE WHEEL TO THE AXLE.

August 18, 2003

United States

Wilson Trailer Company

ON CERTAIN TRAILERS EQUIPPED WITH SEALCO SPRING BRAKE CONTROL VALVE ASSEMBLIES INCORPORATED IN ARVINMERITOR AXLES, PART NOS. 110700 AND 110800, THERE IS A RECESSED AREA ON TOP OF THE VALVE IN WHICH A BRASS GUIDE PIN FITS DOWN INSIDE THE BODY OF THE VALVE AND IS HELD IN PLACE BY A STEEL SNAP RING.

August 15, 2002

United States

Wilson Trailer Company

ON CERTAIN TRAILERS EQUIPPED WITH BENDIX SR-2, SR-4, AND SR-5 TRAILER SPRING BRAKE VALVE ASSEMBLIES, THE MOLDED RUBBER FACE OF THE INLET/EXHAUST VALVE (I/E VALVE) COMPONENT OF THE AFFECTED VALVES CAN SEPARATE FROM THE VALVE'S METAL INSERT. AIR CAN BE TRAPPED BY A SEPARATED I/E VALVE CAUSING IT TO BALLOON AND BLOCK…

November 13, 1974

United States

Wilson Trailer Company