Honda

January 4, 2010

United States

Honda (American Honda Motor Co.)

HONDA IS RECALLING CERTAIN MODEL YEAR 2006 AND 2007 RIDGELINE VEHICLES MANUFACTURED BETWEEN JANUARY 17, 2005, AND JUNE 7, 2006. A WIRING HARNESS CONNECTOR FOR THE HEATING, VENTILATION AND AIR CONDITIONING (HVAC) BLOWER MOTOR LOCATED UNDER THE PASSENGER'S SIDE OF THE INSTRUMENT PANEL MAY BE ACCESSIBLE TO KICKING BY…

November 20, 2009

European Union

Honda

The product poses a risk of injuries because the mounting bolts on the rear brake master cylinder may not be properly tightened and could possibly come loose during use affecting the operation of the rear brake.

November 13, 2009

European Union

Honda

The product poses a risk of injuries because three weld spots are missing from the front wing and this may alter the crash behaviour in the event of an accident.

November 6, 2009

European Union

Honda

The product poses a risk of injuries because the weld seam on the left-hand side of the swing arm may be incorrectly positioned which could cause the swing arm to break while the motorcycle is being ridden and thus cause an accident.

September 17, 2009

United States

Honda (American Honda Motor Co.)

HONDA IS RECALLING CERTAIN MODEL YEAR 2002 VTX1800 MOTORCYCLES MANUFACTURED BETWEEN AUGUST 14 AND OCTOBER 4, 2001. THE SWINGARM MAY NOT HAVE BEEN PROPERLY WELDED.

May 21, 2009

United States

Honda (American Honda Motor Co.)

HONDA IS RECALLING 12,894 MY 2008 CBR1000RR MOTORCYCLES. A COOLANT HOSE CLAMP LOCATED ON THE WATER PUMP COVER MAY BREAK DUE TO FATIGUE CAUSED BY VIBRATION GENERATED AT CONTINUOUS HIGH ENGINE SPEEDS.

April 17, 2009

European Union

Honda

The product (Vehicle type GG2 and GG3) poses a risk of injuries because one of the screws attaching the head airbag may be missing. Each head airbag is fastened with six screws on each side.

April 10, 2009

European Union

Honda

The product poses a risk of injuries because the speedometer may display incorrect information. Water may get into the wiring and build up in the U-shaped protection tube for the ground wire.

March 27, 2009

European Union

HONDA

The product poses a risk of injuries because the locating bolt was not fitted initially and was then missed as the installed seat belt obscured the locating bolt hole from the operator's view. If the locating bolt is missing, the seatbelt's Emergency Locking Retractor (ELR) can move during usage potentially loosening…

February 18, 2009

United States

Honda (American Honda Motor Co.)

HONDA IS RECALLING 421 MY 2009 ODYSSEY VEHICLES. DURING ASSEMBLY, INCORRECT FRONT BRAKE HOSES WERE INSTALLED.

January 30, 2009

European Union

Honda

The product poses a risk of injuries due to a possible anomaly in the welding on the right-hand side of the swing arm. In certain driving conditions, the welding may fail and the swing arm could break, causing an accident in which the rider may be seriously injured.

November 21, 2008

European Union

Honda

The product poses a risk of injuries because part of the rear light may not function, causing the level of light emitted to fall below the approved standard, thus posing the risk of an accident. European Union

Honda

The product poses a risk of injuries because the internal push rod within the handbrake assembly may have been damaged during manufacture of the parking brake. This damage can lead to the joint 'jamming' and subsequently the handbrake may not engage or in some cases it may release itself.

November 14, 2008

European Union

Honda

The product poses a risk of injuries because one of the two screws used to mount the bank angle sensor may not be sufficiently tight. If the sensor becomes loose, the engine may cut out.

October 14, 2008

United States

Honda (American Honda Motor Co.)

HONDA IS RECALLING 128 MY 2008-2009 CIVIC SEDANS. A BRACKET THAT COVERS THE FUEL HOSE CONNECTOR IS SECURED WITH A BOLT AND NUT, BUT DURING ASSEMBLY THE NUT WAS NOT INSTALLED.

October 3, 2008

European Union

Honda

The products pose a risk of injuries because the cable guide plates have not been welded securely, and this could cause the brake cable to become slack. Should this happen, the vehicle may roll away unexpectedly when parked on a slope.

September 19, 2008

European Union

HONDA

The product poses a risk of injuries because of incorrect spot welding of the handbrake lever assembly which may cause internal separation of the guide plates. This will prevent correct tension being applied to the brake cables when the handbrake is engaged.

August 8, 2008

European Union

HONDA

The product poses a risk of burns because strong vibrations intensified by high engine speed may cause the coolant hose clamp fitted to the water pump nozzle to break, allowing hot coolant to leak onto the rider's left foot, which, in the worst case, may lead to scalding.

July 29, 2008

United States

Honda (American Honda Motor Co.)

HONDA IS RECALLING 241 MY 2008 ELEMENT VEHICLES. THE FRONT BUSHING BRACKET OF THE LEFT TRAILING ARM OF THE REAR SUSPENSION MAY HAVE BEEN IMPROPERLY WELDED AND COULD SEPARATE FROM THE TRAILING ARM.

June 20, 2008

European Union

HONDA

The product poses a risk of fire because if the terminal and wire are incorrectly inserted in the ACG stator plug, the resistance of the contact in the terminal exceeds the standard value necessary, generating heat in the connection and resulting in the separation of the two parts. Once separation occurs, the…