Generalllc

April 8, 1997

United States

General Motors, LLC

VEHICLE DESCRIPTION: PASSENGER VEHICLES AND MINI VANS ORIGINALLY SOLD OR CURRENTLY REGISTERED IN THE FOLLOWING STATES: CONNECTICUT, ILLINOIS, INDIANA, MAINE, MASSACHUSETTS, MICHIGAN, NEW HAMPSHIRE, NEW JERSEY, NEW YORK, OHIO, PENNSYLVANIA, RHODE ISLAND, VERMONT AND WISCONSIN. THE REAR CRADLE BOLTS PULL THROUGH THE… United States

General Motors, LLC

THE OUTBOARD SAFETY BELT WEBBING ON THE RIGHT-HAND REAR BUCKET SEAT CAN SEPARATE DURING A VEHICLE CRASH. United States

General Motors, LLC

IT IS POSSIBLE TO REMOVE THE IGNITION KEY WHILE THE CYLINDER IS IN THE RUN POSITION. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FEDERAL MOTOR VEHICLE SAFETY STANDARD NO. United States

General Motors, LLC

VEHICLE DESCRIPTION: G VANS EQUIPPED WITH 6. 5L TURBO-CHARGED DIESEL ENGINES.

March 20, 1997

United States

General Motors, LLC

THE REAR SUSPENSION TIE ROD ASSEMBLY CAN FRACTURE. United States

General Motors, LLC

IF THE AIR BAG COMPUTER IN A SUBJECT VEHICLE EXPERIENCES A MECHANICAL SHOCK (I. E. United States

General Motors, LLC

VEHICLE DESCRIPTION: ELECTRIC VEHICLES. THESE VEHICLES WERE BUILT WITH A DRIVE MOTOR CHARGER RECEPTACLE ASSEMBLY THAT WAS INCOMPLETELY SEALED.

March 11, 1997

United States

General Motors, LLC

THESE VEHICLES WERE ASSEMBLED WITH CENTER REAR SEAT BELT ANCHOR BOLTS NOT PROPERLY INSTALLED. THIS DOES NOT MEET THE REQUIREMENTS OF FMVSS NO.

March 7, 1997

United States

General Motors, LLC

VEHICLE DESCRIPTION: EXTENDED CAB AND 2-DOOR UTILITY VEHICLES EQUIPPED WITH RECLINING SEATS AND THE EASY-ENTRY FEATURE. THESE VEHICLES EXHIBIT A CONDITION IN WHICH A PINCH POINT EXISTS IN THE RECLINER MECHANISM THAT CAN TRAP AND PINCH A PERSON'S HAND OR FINGER(S) WHEN THE EASY-ENTRY FEATURE IS ACTIVATED.

February 11, 1997

United States

General Motors, LLC

SOME OF THESE VEHICLES HAVE A STRAINED OR SEPARATED WASHER/WIPER SWITCH POWER FEED WIRE.

January 27, 1997

United States

General Motors, LLC

THE TOP COAT PAINT SEVERELY PEELS DUE TO OVERBAKING OF THE POWDER PRIMER PRIOR TO THE TOP COAT APPLICATION. SINCE THE WINDSHIELD PRIMER AND ADHESIVE ADHERE TO THE TOP COAT PAINT ONTHE WINDSHIELD OPENING FLANGE, THE WINDSHIELD DOES NOT COMPLY WITH FEDERAL MOTOR VEHICLE SAFETY STANDARD NO.

December 17, 1996

United States

General Motors, LLC

THE FRONT AND/OR REAR HAZARD WARNING LAMPS (FOUR-WAY FLASHERS) DO NOT FLASH WHEN THE HAZARD SWITCH IS ACTIVATED. THIS FAILS TO COMPLY WITH FMVSS NO. United States

General Motors, LLC

THE STEERING COLUMN LOWER PINCH BOLT WAS NOT PROPERLY TIGHTENED DURING ASSEMBLY.

December 10, 1996

United States

General Motors, LLC

THE WHEEL LUG NUTS WERE NOT TIGHTENED TO THE PROPER SPECIFICATION DURING ASSEMBLY.

November 14, 1996

United States

General Motors, LLC

VEHICLE DESCRIPTION: 4-DOOR, 4-WHEEL DRIVE AND ALL-WHEEL DRIVE MULTI-PURPOSE PASSENGER VEHICLES. DURING DEVELOPMENT TESTING, THE PROP SHAFT CONTACTED THE INBOARD SIDE OF THE FUEL TANK ALLOWING FUEL LEAKAGE.

November 4, 1996

United States

General Motors, LLC

THE RECLINER MECHANISM AND THE SEAT FRAME MAY HAVE FOAM AND/OR VINYL VETWEEN THEM, CREATING A "SOFT" JOINT. THIS "SOFT" JOINT RESULTS IN LOWER THAN SPECIFIED BOLT TORQUE WHICH LEADS TO JOINT LOOSENESS, CAUSING BOLT FATIGUE AND EVENTUAL BOLT FAILURE. United States

General Motors, LLC

THESE VEHICLES WERE MANUFACTURED WITH SEAT BELT RETRACTORS OUT OF DESIGN POSITION WHICH CAN CAUSE THE RETRACTOR TO LOCK-UP ON SLOPES LESS SEVERE THAN THE FMVSS REQUIREMENT. THIS DOES NOT COMPLY WITH FMVSS NO.

October 30, 1996

United States

General Motors, LLC

DURING ASSEMBLY OF THE LEFT REAR QUARTER PANEL, SOME WELDS WERE MISSED. THIS DOES NOT COMPLY WITH THE REQUIREMENTS OF FMVSS NO.

October 28, 1996

United States

General Motors, LLC

DURING DEPLOYMENT OF THE PASSENGER AIR BAG, THE AIR BAG FABRIC CAN SNAG ON A REINFORCEMENT INSIDE THE INSTRUMENT PANEL, CAUSING THE EXPANDING AIR BAG TO LIFT THE INSTRUMENT PANEL PAD AND THEN DEPLOY UNDER THE INSTRUMENT PANEL INSTEAD OF THROUGH THE DOOR IN THE INSTRUMENT PANEL.

October 8, 1996

United States

General Motors, LLC

THE SEAT COVER TRIM MATERIAL DOES NOT MEET THE FLAMMABILITY REQUIREMENTS OF FMVSS NO. 302, "FLAMMABILITY OF INTERIOR MATERIALS.